McLaren Wheel Fitment: Bolt Pattern, Sizes and Offsets

Most current McLaren Sports Series cars, including the 570S, 600LT, 650S, 675LT and 720S, use a 5x112 bolt pattern with M14 x 1.5 lug bolts. That number only tells you the wheel can bolt on. Whether it fits comes down to center bore, offset, width and caliper clearance, and those change from model to model and from brake option to brake option. This guide gives you the specs, the factory sizes we can document, and the checks that keep a wrong wheel from reaching your garage.
If you are hunting for a specific McLaren wheel, center cap, lug bolt or TPMS sensor, our McLaren parts and cars section lists them, and the AI-driven parts search on the site helps you narrow a listing down to the exact part for your car.
TL;DR
- The 570S, 600LT, 650S, 675LT and 720S are listed with a 5x112 bolt pattern, and the 570S, 600LT, 720S and GT with M14 x 1.5 threads.
- The 720S is listed with a 57.1 mm center bore, so wheels with a larger bore need hub-centric rings.
- Factory sizes are staggered: a narrower 19-inch wheel in front and a wider 20-inch wheel at the rear. Keep that stagger when you change wheels.
- Offset, width and brake caliper clearance decide the fit. Confirm them against your exact car, not only the model name.
- Buy from a source that lists parts by model and year, so the wheel you order matches the car in your garage.
Table of Contents
- What “fitment” means on a McLaren
- McLaren bolt pattern and hub specs
- Factory wheel and tire sizes by model
- Offset: where most wheel mistakes happen
- Brake clearance: carbon ceramics and calipers
- Center bore, hub rings and lug hardware
- Aftermarket wheels and spacers
- A fitment checklist before you buy
- Our view on McLaren wheel fitment
- Find McLaren wheels and parts
- FAQ
- Sources
What “fitment” means on a McLaren
A wheel fits when it matches the car in every dimension that matters, not only the bolt holes. Fitment guides break it into these checks: the bolt pattern, center bore, offset, diameter and width, brake caliper clearance, load rating and lug hardware all have to agree. Miss one and you get vibration, rubbing, a wheel that will not sit flat on the hub, or a rim that touches the caliper.
Here is each term in plain words:
- Bolt pattern (PCD): the number of lug holes and the diameter of the circle they sit on. “5x112” means five holes on a 112 mm circle.
- Center bore: the hole in the middle of the wheel that slides over the hub. A tight match centers the wheel on the hub rather than on the lug bolts.
- Offset (ET): the distance in millimeters from the wheel’s mounting face to its centerline. Lower offset pushes the wheel outward, higher offset pulls it inward.
- Width and diameter: written like 19x8.5, meaning 19-inch diameter and 8.5-inch width.
- Seat type: the shape where the lug bolt meets the wheel. M14 x 1.5 bolts with a 60-degree cone seat are listed for the 720S.
McLaren bolt pattern and hub specs
The answer most owners search for is short. The Sports Series cars from the 570S through the 720S, plus the GT, are listed at 5x112. The same list gives M14 x 1.5 threads for the 570GT, 570S, 600LT, 720S and GT.
For the 720S, one fitment database lists the following (FitmentSpec):
| Spec | 2023 McLaren 720S |
|---|---|
| Bolt pattern | 5x112 |
| Center bore | 57.1 mm |
| Lug bolts | M14 x 1.5, 60° cone seat |
| Torque | 96 ft-lbs (130 Nm) |
| Safe offset range | +35 to +48 mm (flush target +40) |
An independent French database agrees on the core numbers for the 720S built 2017 to 2023: 5x112, a 57.1 mm bore, M14x1.50 bolts and 130 Nm of tightening torque. A third table lists the older 650S and 12C with 5/112, ET47, a 57.1 mm bore and M14x1.50 studs.
Two cautions apply. First, specs can vary with brake option and trim, so confirm them on your car, using the door-jamb placard or a mechanic who works on McLarens, before you mount anything. Second, community threads sometimes quote a different bore figure for the 570S. If a number does not match your hub, measure the hub before you order wheels instead of assuming.
And always tighten to the torque in your owner’s manual. The 130 Nm figure above is the one published for the 720S, so use the figure for your own model.
Factory wheel and tire sizes by model
Every McLaren in this range runs a staggered setup. The front wheel is smaller and narrower, the rear is larger and wider. These are the sizes we can tie to a spec sheet:
| Model | Front | Rear |
|---|---|---|
| 570S (2018 catalog) | 19x8.0J, 225/35R19 | 20x10.0J, 285/35R20 |
| 650S Spider (2016) | 19x8.5, 235/35YR19 | 20x11, 305/30YR20 |
| Artura | 19x8.5J, 235/35R19 | 20x10.5J, 295/35R20 |
| 720S (2017 to 2023) | 245/35R19 | 305/30R20 |
The 570S catalog also notes that the standard wheel is a Sport 10-spoke cast alloy, with lightweight forged designs as options. The Artura’s spec sheet lists Pirelli P Zero and P Zero Corsa tires.
Notice how the numbers move. The 570S and 650S share a bolt pattern but not a rear width: 10.0 inches against 11 inches. Wheel diameter can look identical across models while width, offset and tire size differ. That is why a part number or a model-and-year match matters more than “it’s a McLaren wheel.”

Tire sizes by model
Tire size follows the wheel. A tire has to suit the wheel’s width, and the staggered front and rear sizes should stay in the same relationship to each other. A fitter or the owner’s manual will give the speed and load rating for your car. The Artura listing above, for instance, shows a 91Y front and 105Y rear rating alongside its sizes. When in doubt, match the rating printed on the tire currently on your car.
Offset: where most wheel mistakes happen
Bolt pattern is yes or no. Offset is a range, and it is where mismatches appear. One table of reference data warns that its offset figures are averages for typical rim sizes, that larger rims often need a larger offset, and that a wrong offset can make the wheel touch the brake caliper, control arm or fender. The same source notes that a wheel standing too far out of the arch throws gravel and stones at the body and at other road users.
For the 720S, the database figures above give a safe range of +35 to +48 mm, aiming near +40 for a flush look. Other published tables list wider factory ranges for the 570S, so treat any single figure as a starting point for your model and year, not a guarantee.
Some practical rules:
- Check the front and rear separately. Offsets are not the same on both axles.
- Match the wheel’s offset to its width. A wider wheel at the same offset sits further out on both sides.
- Allow for suspension changes. Lowering a car, or fitting different springs, changes how much room the tire has in the arch.
- Check full steering lock. A wheel that clears when the car is straight can touch an arm or liner when turned.
Brake clearance: carbon ceramics and calipers
The 570S catalog lists carbon-ceramic brakes with six-piston front and four-piston rear calipers. Big calipers mean a wheel’s inner barrel and spoke shape matter, not just its diameter. Two wheels with identical size and offset can differ in how they clear a caliper. Test-fit one wheel on one corner, and check there is a gap all around the caliper before you mount the full set.

Brake option also changes specs. One fitment source notes that hub tolerances and torque values vary by brake option and trim. If your car has uprated brakes, make sure the wheel listing says it clears them.
Center bore, hub rings and lug hardware
Many aftermarket wheels are made with a bore larger than the 57.1 mm hub, so they can fit several makes. Then a hub-centric ring fills the gap. The 720S source above gives the example of a 73.1 mm to 57.1 mm ring. Without it, the wheel centers on the lug bolts alone, which is a common cause of vibration at speed.
Lug hardware is the other half. M14 x 1.5 with a 60-degree cone seat is listed for the 720S. A ball-seat or flat-seat bolt does not seat properly in a cone-seat wheel. If the wheel is not made for that seat, the bolt will not clamp it correctly, and that is a safety issue, not a cosmetic one. Use the correct hardware for your wheel and torque it to the figure for your car.
Aftermarket wheels and spacers
Owner threads show a wide range of aftermarket setups on the 570S, 650S and 720S. Common reports include 19-inch fronts with 20-inch rears at sizes close to factory, and a more aggressive 20-inch front with 21-inch rear. Some builders report that these fit with the correct offsets and no spacers. Others install spacers, often a few millimeters in front and more at the rear, to get the wheel to sit where they want it.
Treat those reports as leads, not specs. They come from individual cars with their own suspension height, tire choice and brake package. Before you order a set:
- Ask the wheel maker for the exact offset and bore for your model and year.
- Confirm the wheel is rated for the car’s weight and performance.
- Confirm the tire size you plan to fit works on that wheel width and keeps overall diameter close to factory.
- Keep the staggered front and rear relationship.
Spacers change the effective offset. They also add another part between hub and wheel, so they need to be the right thickness, bolt pattern, bore and hardware. A well-chosen offset usually beats adding spacers later.
A fitment checklist before you buy
- Identify the exact model, year and brake package. A 650S and a 720S are not the same.
- Confirm bolt pattern, center bore and thread against the car, using the door-jamb placard or a McLaren specialist.
- Compare wheel width and offset front and rear with the factory numbers for that car.
- Verify caliper clearance, especially with carbon ceramic brakes.
- Check the hardware: thread, seat type and bolt length.
- Confirm tire sizes and ratings suit the car, and keep the stagger.
- Check TPMS compatibility, since the wheel has to accept your sensors.
- Inspect used wheels for bends, cracks, curb damage and corrosion at the hub face.
On used wheels, a clean surface also makes cracks and corrosion easier to see. If you are preparing a set for inspection or fitting, removing brake dust safely before you check the faces and barrels gives you a clear view of the metal.
Our view on McLaren wheel fitment
Most fitment problems we see discussed come from one shortcut: matching the bolt pattern and stopping there. A 5x112 pattern is shared across several McLaren models, so it narrows the field very little.
What protects you is matching the wheel to the car by model and year. That is why we organize our McLaren listings around the cars themselves, and why our AI-driven parts search is built to find a precise part for a rare or high-performance car quickly.
With more than 365,000 listings covering exotic and supercar parts, the site is designed so you can compare a wheel, a hub part or lug hardware against your car’s details and not against a vague category. Sellers can list parts with 0% commission, and that helps more owners and shops bring hard-to-find parts to market.
Our advice: write down your car’s model, year, brake option and factory sizes first. Then search. A wheel that fits the numbers is much easier to find when you know what the numbers are.
Artem
Find McLaren wheels and parts
Supercars.parts is a marketplace with more than 365,000 listings for exotic and supercar parts, from Ferrari and Lamborghini to McLaren, Aston Martin and Rolls-Royce. Its AI-driven search is designed to help you locate a precise part quickly. Start from McLaren parts and cars, or go to the page for your model, such as the McLaren 570S Sprint, the 650S Coupe or the Artura. For other makes, the exotic car parts section covers the full catalog.

If you own a Lamborghini as well, our guide to Lamborghini wheel fitment walks through the same checks for that brand.
FAQ
What is the bolt pattern on a McLaren 720S?
The 720S is listed with a 5x112 bolt pattern, meaning five lugs on a 112 mm circle. The same source lists a 57.1 mm center bore and M14 x 1.5 lug bolts. Confirm the figures against your car’s door-jamb placard before ordering.
Do all McLarens use the same bolt pattern?
No. The 570GT, 570S, 600LT, 650S, 675LT, 720S and GT share 5x112, but width, offset and tire size differ between them. A shared bolt pattern does not make wheels interchangeable.
Do I need spacers on aftermarket McLaren wheels?
It depends on the wheel’s offset and your car. Some owners report using spacers, and others report none with the correct offset. A wheel made with the right offset for your model and year is the cleaner route, and any spacer must match the bolt pattern and center bore.
What torque should I use for McLaren wheel bolts?
For the 720S, published figures are 130 Nm (96 ft-lbs). Other models can differ, so use the figure in your owner’s manual and retorque as that manual advises.
Are McLaren front and rear wheels the same size?
No. They are staggered, with a narrower front wheel and a wider rear one, as the Artura spec sheet shows with 19x8.5J front and 20x10.5J rear. Keep that stagger when you change wheels.
Sources
- McLaren Wheel Interchangeability Guide
- Bolt-pattern.com bolt pattern guide
- 2023 McLaren 720S wheel fitment specs
- McLaren 720S (2017 to 2023) specifications
- McLaren bolt pattern list
- McLaren Artura technical specifications
- 2018 McLaren 570S catalog
- 2016 McLaren 650S Spider specs
- Removing brake dust safely